We do all kinds Of engines Please feel free to contact us 586-781-3656
Cylinder Head Work
High Performance valve job (two valves per cylinder)
8 cylinder…….$200
6 cylinder…….$175
4 cylinder…….$155
Stock valve job (two valves per cylinder)
8 cylinder.....$155
6 cylinder…….$145
4 cylinder…….$125
Add $30 for aluminum heads.
Add $50 for overhead can heads with cams installed.
Hourly rate of $75 charged to make valve adjustments done by grinding lash caps or for multiple valve heads with more than 2 valves per cylinder.
Cut spring seat for installed height $5 each
Cut spring seat for larger O.D. spring $5 each
Machine guide for more guide to retainer clearance $4 each
Machine guide for Teflon seal $4 each
Hone valve guide for oversize valves $4 each
R&R removable valve guides $10 each
Machine & install bronze valve guides $16 each
Machine & install bronze guide liners $12 each
Resurface head on Peterson grinder $35 per head
Resurface head on storm Vulcan up to .020” $50 per head
Cut intake side of head with no lip $50 per head
Cut intake side of head with lip $70 per head
C.C. one chamber in head $25 per head
Porting
Prices listed below are for aluminum heads. Add 25% for cast iron heads.
Street Port heads (bowl area, match gaskets to port, 0.5” V-8) $550 per pair
Street Ports heads with full exhaust port $750 per pair
Pro Street Port heads (bowls, full intake & exhaust) $950 per pair
Full Race Port heads $1500 per pair
Port Aluminum Intake Manifold $195 each
Blocks
Boring & Honing with CK-10 machine
Up to.030” $25 per cylinder
Up to .060” $30 per cylinder
Up to .090” $40 per cylinder
Up to .120” $50 per cylinder
Up to .150” $60 per cylinder
Add 25% to above prices to offset bore blocks
Add hone plates, if available, to above prices at $50 per block
Bore & hone one cylinder only $75
Clean up hone in CK-10 $10 per cylinder
Clean up hone with glaze breaker $7 per cylinder
Hone lifter bores (.001) $4 each
O-ring cylinder bore $15 each
Sleeves installed 3/32” wall $100 per sleeve
Sleeves installed 1/8” wall $110 per sleeve
Diesel sleeves installed $150 per sleeve
Clearance block for stroker crank or rods $200 per block
Remove casting flash & deburr block $100 per block
Bore Buick oil pump pickup passage in block to 9/16” $100 per block
Notch block for valve clearance $15 per notch
Remove cam bearings $20 per block
Install cam bearings $30 per block
Remove or install freeze plugs $25 per block
R&R oil galley plugs $30 per block
R&R oil galley plugs for big block Chevy $40 per block
Remove press in oil plugs & install screw in plugs $15 per hole
Sonar check block with report $100 per block
Pressure check block $100 per block
Fill block with grout $100 per block
Resurface block- clean up for inline engines $65 per block
Resurface block – clean up for V type engines $100 per block
Resurface block to special spec. with BHJ plates * $200 per block
*up to .015” then add $10 per additional .10” removed per side
Resurface manifold pad on block up to .050” $65 per block
Align- boring main bores in block $160 per block
Align- honing main bores in block $160 per block
Install 4 bolt caps in 2 bolt blocks, straight bolt $80 per block
Install 4 bolt caps in 2 bolt blocks, splayed bolts $95 per block
If other than original caps for that block, ADD $50 per block
If caps have to be machined to fit block, ADD $50 per block
Crankshafts
Grind crank $150
Polish crank $25
Chamber oil holes $35
Cross drill crank $100
Drill & tap crank snout for bolt $50
Weld one journal on crank $40
Magnaflux crank $50
Knife edge crank counterweight $200
Reduce outer diameter of crank counter weights $200
Pistons
Radius piston domes $20 each
Machine wedge piston flat top up to .030” $12 each
Machine existing notch deeper $10 per notch
Layout & machine piston with no notch $20 each
Balancing
Balancing complete assemblies V-8 $175
V-6 or V-4 $200
8 cylinder inline $160
6 cylinder inline $155
4 cylinder inline $150
Balancing 90° opposed engine is same price as comparable inline
Strokers or destrokers ADD $50
Other than stock assemblies ADD $25
If Mallory metal is needed ADD $37 per inch of Mallory used.
Labor to install Mallory metal is $65 per hour.
All machine work must be done before balancing.\Parts necessary for complete balance job:
- all pistons & pins
- all rods, caps & nuts
- all writ pin locks
- two sets of rods bearings
- rings for one piston
- crank shaft and keys
- harmonic dampner, bolts & washers
- crank pulleys, bolts & washers
- crank timing gear
- flywheel or flexplate & bolts
- pressure plate & bolts
- There is an extra charge for assembly, disassembly and cleaning parts.
Ferrous Cleaning
Degreasing Block $50
Head $25 each
Crank $25
Manifold $25
Oil Pan $20
Valve covers $20 per pair
Aluminum Cleaning- add 25% to above prices
Shot Peening & Glass Beading (item must be degreased)
Glass bead block $125
Glass bead heads $25 per head
Glass bead intake manifold $40
Glass bead rods $6 per rod
Shot pean rods $10 per rod
Assembly & Disassembly
Disassemble engine & inspect $100
Assemble short block $450
Assemble long block $550
Assemble complete engine & prime oil system $650
Press piston from rod $4 each
Assemble press fit rod & piston $5 each
Assemble or disassemble floating rod & piston $5 each
ADD 25% for Spirolox
Complete blueprinting of engine $1500 plus machining
Miscellaneous
Champher rod or main bearing $5 per bearing
Drill rod bearings for pinned rods $5 per bearing
Recurve clean distributor $49 plus parts
Resurface flat flywheel $35
Resurface recessed flywheel $50
Turn brake drum $10 each
Turn ferrous brake rotor $12 each
Grind break shoes to match radius of drum $5 per wheel
Heli Coil hole $35 each
Additional Notes:
- · Shop time or consultation fees not mentioned elsewhere in this price sheet are set at $65 per hour. Projects requiring a substantial amount of time can be negotiated at contract signing.
- · Prototype estimates will be strictly time and material unless stated in writing and signed by both parties.
- · There is5% fee for miscellaneous sealers, lubricants, environmental, clean up, etc. up to a maximum of $25.
- · There is a $25 hazardous material disposal fee for engines that are brought in full oil or antifreeze.
- · Items left over 30 days after completion and notification will be sold for charges.
- · All quotes requiring disassembly are by hourly rates only, Advance payment is required.
- · Prices are subject to change without notice.
